Bob Drake Catalog

FLATHEAD

http://www.bobdrake.com

IDLE JETS

Not often a problem,

but we’ve got them if

you need them. They

must seal securely in the

casting on that angled

seat just below the cross-

hole at the top end.

9542K $17.00 pair

POWER BY-PASS VALVES

Standard factory power-valve (power by-pass jet),

with new fiber-gasket, for Stromberg 48 and 40

carburetors at sea level. Also fits Stromberg 97, 81,

LZ and other models.

No. 63..........9594K-63

No. 65..........9594K-65

No. 67..........9594K-67

No. 69..........9594K-69

No. 71..........9594K-71

Your Choice $13.00 each

ACCELERATOR PUMP ROD

FOR 97/48/40

Full accelerator-pump kit for Stromberg

97, 48 and 40 carburetors. Includes new

springs, retainer, washers, felt gasket

and cotter pin.

9630K $20.00 kit

ACCELERATOR PUMP KIT FOR 81

Talk about original. Our Stromberg 81

accelerator pump has the correct 10-finger

brass spring-washer and small bore leather

seal. The kit includes new springs, retainer,

washers, felt gasket and cotter pin.

9630K-81 $26.00 kit

CABLE CHOKE BRACKET

A perfect replica - in stainless steel -

of the cable-choke mounting bracket

that came with ‘49-’53 Fords. This

separate bracket (included with our

9510A-C cable-choke carburetor) -

mounts off the rear body screw to

hold the choke-cable sleeve.

9552K-B $22.00 each

KICKER ASSEMBLY /

CABLE CHOCK

A perfect replica - in stainless steel - of

the 97 kicker assembly for cable choke

(designed for ‘49-53 Fords). A separate

bracket - included - mounts off the

rear body screw to hold the choke-

cable sleeve.

9552K-C $50.00 each

SUPERLINK ARM & SWIVEL

A new take on the traditional multi-carb linkage
arm. Zinc die-cast with a modern H-beam
section for strength without excess
weight, and a small feature-line at
the bottom edge for a period feel.
The counter-sunk stainless steel screw
matches those on the carb and threads directly
into the arm. The stainless steel swivel, secured
by a small e-clip on the back, has a cross-hole
sized for the typical 3/16" diameter linkage rod,
secured by a black knurled-tip set-screw.

9091K $16.00 each

BRASS FLOAT & HINGE PIN

Fits 97, 81, 48, 40 and other

models too. Made on the

original Stromberg tooling.

Pressure tested, of course,

and supplied with a new float

hinge-pin.

9550K $22.00 set

BOWL PLUG GASKETS

If your Stromberg is leaking

from underneath, these

could be the answer.

9563K $5.00 set

S-JET INLET VALVE

The Genuine Stromberg

twin-ball S-jet is the ‘next

generation’ needle and seat.

It’s designed to eject dirt

particles and improve high-

speed running and, unlike

many so-called viton-tipped

needle valve, it won’t stick

or melt in today’s corrosive

new gas formulas. Comes

with a new fiber washer. Fits

Stromberg 97, 48, 81 and 40.

9564K $17.00 each

MAIN JETS
Standard factory main jets for
Stromberg 48 and 40 carburetors
at sea level. Two jets. Installs with
Genuine Stromberg jet wrench -
9071K.

0.035 inch....9533K-35

0.041 inch.... 9533K-41

0.043 inch....9533K-43

0.045 inch....9533K-45

0.048 inch....9533K-48

Your Choice $10.00 pair

1933-38

STROMBERG

NEEDLE & SEAT KIT

This is the correct

replacement. 3 piece kit.

40-9564 $16.00 kit