AWS EDITION 1, 2009

193

© 2009, AWI, AWMAC, WI - Architectural Woodwork Standards - 1st Edition, October 1, 2009

As may be updated by errata at http://www.awinet.org, http://www.awmac.com, or http://www.woodworkinstitute.com/awserrata/

Section 8 - Wall Surfacing (Page 22 of 32)

PRODUCT

MATERIAL, MACHINING, AND ASSEMBLY RULES (continued)

DESCRIPTION E C P



4.4

A S S E M B L Y 

ASSEMBLY (continued)



4.4.4

W O O D V E N E E R

At WOOD-VENEER wall surfacing (continued)



4.4.4.2

V E N E E R M A T C H

VENEER MATCH at (continued)



4.4.4.2.2

Custom made-to-order SEQUENCE BALANCED-MATCH panels (continued)

4.4.4.2.2.3 1/2" (12.7 mm) less than the adjoining leaf. M

4.4.4.2.3 Panel to adjoining panel requires VENEER GRAIN to align vertically and/or horizontally

within a maximum of:

4.4.4.2.3.1 Unlimited. M

4.4.4.2.3.2 1/4" (6.4 mm) variance. M

4.4.4.2.3.3 1/8" (3.2 mm) variance. M

4.4.4.2.4 Panels WITHIN A ROOM utilizing:

4.4.4.2.4.1 The FULL WIDTH of PREMANUFACTURED SETS are

required to be balance-matched with veneer alignment;

however:

MM

4.4.4.2.4.1.1

This requirement does not apply to the trimmed side

of a make-up panel.

4.4.4.2.4.2

SELECTIVELY REDUCED WIDTH of PREMANUFACTURED SETS,

are NOT required to be balance-matched or have veneer alignment.

4.4.4.2.4.3

CUSTOM-SEQUENCED MATCH are required to be

balance-matched with veneer alignment, including make-

up panels.

MM

4.4.4.2.4.4

BLUEPRINT MATCH are required to be balance-matched

with veneer alignment at common size panels, make-up

panels, and components.

MM

4.4.4.3 BUTT JOINTS shall:

4.4.4.3.1 NOT be shop-prepared. M

4.4.4.3.2 Be plant-prepared with edges eased. M

4.4.4.3.3 Be plant-prepared and grooved with splines furnished and edges eased. M

4.4.4.4 REVEAL JOINTS and CORNERS shall:

4.4.4.4.1 NOT be shop-prepared. M

4.4.4.4.2 Be plant-prepared with edges eased and articulation strip(s) furnished. M

4.4.4.4.3 Be plant-prepared and machined for furnished articulation strip(s) with

edges eased.

M

4.4.4.5 INSIDE CORNERS to be shipped oversize for field fitting.

4.4.4.6 MITERED outside corners shall:

4.4.4.3.6.1 NOT be shop-prepared. M

4.4.4.3.6.2 Be plant-prepared and shipped loose. M

4.4.4.3.6.3

Be plant-prepared, and if site conditions permit, glued and braced prior to

shipping. M

4.4.4.7

FIELD JOINERY shall be factory-prepared to the greatest extent possible with feature

strips and joint trim furnished oversize, where possible, to allow for jobsite fitting. MM

4.4.4.8

EXPOSED CORNERS shall be shoulder-mitered, lock-mitered, spline-mitered, or mitered with a

biscuit joint, unless specified and/or detailed otherwise.

4.4.4.9 MOLDINGS within an individual panel face shall be:

4.4.4.9.1 Shipped loose. M

4.4.4.9.2 Factory-applied. MM

8