Digital Audio Interfacing and Networking 14791 0 0 1 Increasing directivity.
0 1 0 1 Supercardioid.
1 1 0 1 Hypercardioid.
0 0 1 1 Increasing directivities
0 1 1 1 through this state.
1 1 1 1 Figure of eight.
Bits 6–7 Preattenuation Status Echo.
Bit 6 7
State 0 0 No attenuation, default.
1 0 Attenuation 1 (minimum).
0 1 Attenuation 2.
1 1 Attenuation 1 (maximum).
Status Data Page 0 Byte 2—Microphone Switch Monitoring
Bits 0–4 Reserved
Bit 0 1 2 3 4
State 0 0 0 0
0Reserved, must always be set to 0 0 0 0 0.Bits 5–6 Call Buttons
Bit 5 6
State 0 0 No button pressed.
1 0 Button 1 pressed.
0 1 Button 2 pressed.
1 1 Buttons 1 and 2 pressed.
Bit 7 Remote Off.
0 Remote parameter setting is enabled, default.
1 Remote parameter setting is disabled.
Status Data Page 0 Byte 3—Microphone Remote Control Feature
Indicator 1 (sound)
Bit 0 EQ Curve Selection
0 Equalization curve not available, default.
1 Equalization curve available, set using Extended
Command Data Byte 7.
Bit 1 Balance-Width.
0 MS width or XY balance not available, default.
1 MS width or XY balance available, set using
Extended Command Data Byte 6, bits 0–6.
Bit 2 MS-XY Switch.
0 MS or XY selection not available, default.
1 MS or XY selection available, set using Extended
Command Data Byte 6, bit 7.
Bit 3 Limiter.
0 Limiter not available, default.
1 Limiter available, set using Direct Command
Data Byte 2, bit 1.
Bit 4 Gain Control.
0 Signal gain settings not available, default.
1 Signal gain settings available, set using Direct
Command Data Byte 2, bits 2–7.Table 39-3. Status Data Page (Continued)
Bit 5 Low Cut Filter.
0 Low cut filter settings not available, default.
1 Low cut filter settings available, set using Direct
Command Data Byte 1, bits 0–1.
Bit 6 Pattern Control.
0 Directivity pattern settings not available, default.
1 Directivity pattern settings available, set using
Direct Command Data Byte 1, bits 2–5.
Bit 7 Attenuation.
0 Attenuation settings not available, default.
1 Attenuation settings available, set using Direct
Command Data Byte 1, bits 6–7.
Status Data Page 0 Byte 4—Microphone Remote Control Feature
Indicator 2 (control)
Bit 0 Mode 2 Synchronization.
0 External synchronization not available, default.
1 External synchroByte 3.
Bit 1 Dither-Noise Shaping.
0 Dither and noise shaping not available, default.
1 Dither and noise shaping available, set using
Extended Command Data Byte 5, bits 0–3.
Bit 2 Multiple Sampling Frequency.
0 Multiple sampling frequencies not available,
default.
1 Multiple sampling frequencies available, set
using Extended Command Data Byte 5, bits 4–7.
Bit 3 Light Control.
0 Light control selection not available, default.
1 Light control selection available, set using
Extended Command Data Byte 4, bits 0–1.
Bit 4 Test Signal.
0 Test signal selection not available, default.
1 Test signal selection available, set using Extended
Command Data Byte 4, bits 2–3.
Bit 5 ADC Calibrate.
0 ADC calibration function not available, default.
1 ADC calibration function available, set using
Extended Command Data Byte 4, bit 4.
Bit 6 Reset.
0 Reset function not available, default.
1 Reset function available, set using Extended
Command Data Byte 4, bit 5.
Bit 7 Mute.
0 Mute selection not available, default.
1 Mute selection available, set using Direct Com-
mand Data Byte 2, bit 0.
Status Data Page 0 Byte 5—Reserved
All bits of Page 0 Byte 5 are reserved and should be set to 0.
Status Data Page 0 Byte 6—Wireless Microphone Status Flags
Bits 0–4 Reserved.Table 39-3. Status Data Page (Continued)