Knitting - UK (2020-04)

(Antfer) #1
76 knittingmag.com

PATTERNS

cm


1


2


3


4


(^52)
6
7
8
9
10
11
12
13
14
16
15
18
17
20
19
22
21
24
23
26
25
28
27
29
9
11
1
in
3 4 5 6 7 8
10
MASTERCLASS WAVING LACE EDGING
QUICK TECHNIQUE WITH JO ALLPORT



  1. Cast on the 8 stitches and
    work a set-up row, purling all
    the stitches.


Creating a waving lace edging to a project is a lovely way to inish it of. This traditional pattern can be scaled up or down to suit your
needs. It’s an easy pattern, using just k2tog, ssk and yo, as well as the usual knit and purl stitches. I’ve worked this pattern in stocking
stitch with the lace pattern in garter stitch, but you can vary this to achieve the look you want.
Note that the stitch count varies across the rows, returning to the original number at the end of row 24.


  1. The irst 12 rows are worked
    in an increase pattern. Now
    on row 1, a RS side row, to
    achieve the garter stitch
    edging, knit the irst 2 sts.
    Then work a yarn over, a
    k2tog, then another yarn
    over. This increases the stitch
    count by one and creates the
    two lace holes.
    3. Now on row 2, purl the irst
    4 sts to form stocking stitch,
    then knit the last 5 sts. This
    group of 5 knit stitches always
    starts with the yarn over from
    the last row, as you see here.
    Continue to work the same
    pattern at the beginning of each
    RS row: k2, yo, k2tog, yo. This
    increases the stitch count by
    one on every RS row. Once you
    have got to 14 sts, ending with
    a WS row, start the decreases.
    On every WS row the irst set
    of stitches, whose number
    varies across the rows, is always
    purled. The last 5 sts are always
    knitted. This applies to both the
    increasing and the decreasing
    sections of the pattern.
    You can make the waving
    lace bigger or smaller here by
    working more or fewer rows.
    4. Now at the end of row 12,
    all the increases have been
    worked. You can see the lace
    pattern worked in garter stitch
    with the section to the left in
    stocking stitch.
    5. On the irst decrease row,
    row 13, work k1, (ssk, yo) twice,
    then work another ssk, as
    shown here. Working only one
    stitch at the beginning, then
    a decrease, keeps the two
    garter stitch stitches constant
    at the beginning of each RS
    row across the whole pattern.
    The two yarn overs keep the
    lace hole pattern constant too,
    but by working 3 decreases,
    the stitch count goes down by
    1 stitch every RS row.
    6. Now on row 14, a WS row,
    you can see the last 5 sts,
    starting with the yarn over
    from the previous row to be
    knitted as before.
    7. Now at the end of row 24,
    all the decreases have been
    worked, so that the stitch
    count is back to its original
    number and you are ready
    to start row 1 once more. The
    waving pattern is evident. You
    can also easily see the ssk
    stitches, which slant to the left
    for the decreasing section of
    the pattern.
    8. Ready for row 1, you can
    see the irst 5 sts where the
    increasing garter lace pattern
    will be worked. Repeat these
    24 rows until your work is
    approximately 440cm long,
    or will go round the outside of
    the blanket. Note that you will
    need to add enough fullness
    for each corner so that, with
    blocking, it will lie flat. To
    ease the edging around the
    corners, gather it and sew to
    each corner, then block to
    smooth out.

Free download pdf