Machine Drawing

338 Machine Drawing dharm d:\N-Design\Des18-4.pm5 Fig. 18.53 Speed reducer (contd.) 10 5 20 176 10 HOLES, M4 30° 20 10 5 14 9 R5 ...

Assembly Drawings 339 dharm d:\N-Design\Des18-4.pm5 The closed end cover 5 is used on the right side of the worm shaft and faste ...

340 Machine Drawing dharm d:\N-Design\Des18-4.pm5 4 2 1 (^63) 5 Fig. 18.1A Stuffing box 5 4 (^213) Fig. 18.2A Steam engine cross ...

Assembly Drawings 341 dharm d:\N-Design\Des18-4.pm5 (^123) 4 Fig. 18.6A Petrol engine piston 5 8 9 10 3 1 4 6 2 7 Fig. 18.7A Rad ...

342 Machine Drawing dharm d:\N-Design\Des18-4.pm5 3 4 2 1 9 7 5 8 6 Fig. 18.9A Rotary gear pump 5 4 3 2 1 6 9 8 7 9 10 4 7 6 1 3 ...

Assembly Drawings 343 dharm d:\N-Design\Des18-4.pm5 4 3 5 6 7 1 2 (^8910) Fig. 18.15A Square tool post 132 45 6 Fig. 18.16A Clap ...

344 Machine Drawing dharm d:\N-Design\Des18-4.pm5 4 3 2 5 1 7 6 Vertical slide Back plate Fig. 18.17A Shaper tool head slide (^4 ...

Assembly Drawings 345 dharm d:\N-Design\Des18-4.pm5 3 2 8 6 7 1 4 5 Fig. 18.20A Revolving centre 2 4 6 7 8 5 10 1 3 9 Fig. 18.22 ...

346 Machine Drawing dharm d:\N-Design\Des18-4.pm5 8 6 9 7 3 5 2 1 4 Fig. 18.24A Drill jig 1210 6 7 13 4 2 3 11 8 1 5 9 Fig. 18.2 ...

Assembly Drawings 347 dharm d:\N-Design\Des18-4.pm5 6 8 5 3 7 3 4 1 Fig. 18.28A Gate valve 13 8 3 2 6 1 11 12 14 4 7 10 5 9 Fig. ...

348 Machine Drawing dharm d:\N-Design\Des18-4.pm5 2 5 1 4 6 3 Fig. 18.30A Non-return valve (Light duty) 3 4 6 5 1 2 Fig. 18.31A ...

Assembly Drawings 349 dharm d:\N-Design\Des18-4.pm5 2 5 1 4 3 Fig. 18.32A Air cock 9 11 3 2 1 5 7 6 10 8 4 Fig. 18.34A Feed chec ...

350 Machine Drawing dharm d:\N-Design\Des18-4.pm5 8 5 6 9 1 7 2 11 9 4 3 12 10 Fig. 18.35A Pressure relief valve 4 11 7 8 9 14 5 ...

Assembly Drawings 351 dharm d:\N-Design\Des18-4.pm5 2 5 4 1 6 10 7 3 8 9 Fig. 18.37A Spring loaded relief valve 6 5 4 1 2 3 Fig. ...

352 Machine Drawing dharm d:\N-Design\Des18-4.pm5 10 9 2 3 4 1 11 7 8 5 6 Fig. 18.49A Crane hook 6 2 4 5 1 3 Fig. 18.50A V-belt ...

Assembly Drawings 353 dharm d:\N-Design\Des18-4.pm5 6 5 4 7 3 2 1 Fig. 18.51A Screw jack 5 4 1 6 3 2 Fig. 18.52A Pipe vice ...

354 Machine Drawing dharm d:\N-Design\Des18-4.pm5 86 11 12 7 2 1 10 9 5 3 4 Fig. 18.53A Speed reducer ...

355 19.1 Introduction The first step in developing a new machine is the preparation of design assembly drawings. After the drawi ...

356 Machine Drawing dharm d:\N-Design\Des19-1.pm5 (iii) Draw the main outlines and add all the internal features. (iv) Cross-hat ...

Part Drawings 357 dharm d:\N-Design\Des19-1.pm5 The bearing brasses are made of gun-metal, because it has good resistance to cor ...